Equip 650201 rokasgrāmata

Equip 650201
7.3 · 1
PDF rokasgrāmata
 · 2 lapas
Angļu
rokasgrāmataEquip 650201
LCD TV WALL MOUNT BRACKET

TILTING

Universal | 650201

Features

l Supports 58 ~ 94cm (23” ~ 37”) Flat Panel Display
l Distance from TV to Wall: 46mm
l Flexible Adjustment with 0º ~ -10º Tilt
l VESA Mount Standards: Maximum 400 x 200mm
l Hole Pattern: Maximum 420mm Wide and 230mm High
l Universal Mounting Pattern
l Bubble Level Integrated
l Load Capacity: Maximum 75kg (165lbs)
WARNING!
Make sure that any listed parts are not missing or defective. Improper installation would result in personal
injury or damage to equipment. If you have any questions about installation, please visit
http://www.equip-info.net for more assistance.
Hardware Kit
Note: Any of the hardware in kit will be required. Other joint parts are forbidden.

INSTALLATION

Mount Wall Plate on the Wall - The product is designed for mounting on solid brick, concrete or hard wood
batten/studs wall, but plasterboard or paneled wall is not allowed.
(a) Solid Brick, Concrete Block Wall - Use the wall plate
a
as a template to mark 6 holes location on the
wall, three in the top row slots and three more in the bottom row. Make sure these holes are level and there
is at least 200mm between any two holes. Drill these holes with a 10mm masonry bit to at least 60mm in
depth. Insert a concrete anchor
e
into each of these holes. Attach the wall plate to the wall using 6 lag
bolts
d
and 6 lag bolt washers
g
.
(b) Hard Wood Batten/Stud Wall - The wall plate
a
must be mounted to two wood studs. Use a high
quality stud sensor to locate three adjacent studs. It is a good idea to verify where the studs are located
with an awl or thin nail shown in diagram 1-A. Drill a 3mm deep hole at the desired height in each stud using
a 4mm drill bit. Use the wall plate
a
as a template to mark the location of the second hole in each stud.
Pre-drill these holes using the 4mm drill bit as well. Attach the wall plate to the wall using the 4 lag bolts
d
and 4 lag bolt washers
g
. Make sure the wall plate is oriented so the flat surface in the center of the plate in
against the wall shown in diagram 1-B. Note: Do not use any concrete ancher when you mount the bracket
onto hard wood wall.
Mount the TV Rails on the Back of Your Display and Install - Make sure the two TV rails
b
are
mounted at an equal distance from the top of the TV and as close to the center as possible as shown in
diagram 2-A. Knobs should face the outside of the television. Plastic spacers
h
are provided to be used
with M4, M5, M6 and M8 mount screws on TV with curved or recessed back panel as shown in diagram 2-B.
If you mount the TV rails to a television with flat back, you will not need a plastic spacer as shown in diagram
2-C. Make sure these screws are right! Some TVs have shallow threaded inserts; so we have provided 4
extra washers if the provided screws are too long.

Hang the TV on the Wall Plate and Adjust - First hook the TV rails over the top of the wall plate
a
in
diagram 3-A. Then tighten the safety screws on the bottom of TV rails
b
in diagram 3-B. You can adjust
your TV down to 10 degrees at maximum: first loosen one knob, second loosen the other knob and then
adjust the TV whichever degree you want. Finally tighten the two knobs.

Skatiet Equip 650201 rokasgrāmatu šeit, bez maksas. Šī rokasgrāmata ietilpst kategorijā Plakanekrāna balsts, un to novērtēja 1 cilvēki vidēji ar 7.3. Šī rokasgrāmata ir pieejama šādās valodās: Angļu. Vai jums ir jautājums par Equip 650201 vai vajag palīdzību? Uzdod savu jautājumu šeit

Vajadzīga palīdzība?

Jums ir jautājums par Equip un atbilde nav atrodama rokasgrāmatā? Uzdodiet savu jautājumu šeit. Skaidri un visaptveroši raksturojiet problēmu un savu jautājumu. Jo precīzāk raksturosiet savu problēmu un jautājumu, jo vieglāk būs citiem Equip īpašniekiem sniegt jums labu atbildi.

Jautājumu skaits: 0

Vispārīgi
Equip
650201 | 650201
Plakanekrāna balsts
4015867159392
Angļu
Lietotāja rokasgrāmata (PDF)
Dizains
Produkta krāsaMelns
SertifikācijaRoHS
Apvalka materiālsTērauds
Svars&dimensijas
Svars2000 g
Platums450 mm
Augstums270 mm
Montāža
Maksimālais svars (tilpums)75 kg
Montāžas saskarnes saderība (min)400 x 200 mm
Montāžas saskarnes saderība (max)400 x 200 mm
Uzstādīšanas tipsSiena
Papildus informācija
Iepakojuma dimensijas (WxDxH)496 x 226 x 60 mm
Ekrāna izmēra saderība23 - 37 "
Informācija par iepakojumu
Iepakojuma svars2500 g
Ergonomika
Slīpuma leņķis-10 - 0 °
parādīt vairāk

Vai nevarat rokasgrāmatā atrast atbildi uz savu jautājumu? Atbildi uz savu jautājumu varat atrast <i>FAQ</i> sadaļā par Equip 650201 zemāk.

Vai jūsu jautājums nav uzskaitīts? Uzdod savu jautājumu šeit

Nav rezultātu